newlib didn't create makefiles
Jeff Johnston
jjohnstn@redhat.com
Mon Jul 17 22:57:00 GMT 2006
Gerster Jochen-B01096 wrote:
>
> Hi
>
> I'm now back on building the gcc, but the problem is still the same. Building newlib failed.
> Now I used gcc 4.11 and binutils 2.17 and newlib 1.14 without any patch or change
>
> First I create for each module its own build folder Then I build the binutils everything works Then the gcc bootstrap And now I want to build newlib and the problem does still exist
>
> Attacted the newlib configure output and the make output
>
> Thanks!
>
> Jochen Gerster
>
Jochen,
I'm not seeing anything obvious:
Can you append /src/build_newlib/powerpc-eabi/nof/newlib/Makefile?
Have you tried the most current CVS sources to see if a problem has
been fixed? A lot has been done with configuration after 1.14 was created.
-- Jeff J.
>
>
>
> -----Original Message-----
> From: newlib-owner@sourceware.org [mailto:newlib-owner@sourceware.org] On Behalf Of Jeff Johnston
> Sent: Dienstag, 28. März 2006 22:01
> To: Gerster Jochen-B01096
> Cc: newlib@sources.redhat.com
> Subject: Re: newlib didn't create makefiles
>
> Jochen,
>
> Please post your directory setup (i.e. where is newlib, where are the rest of the tools). I would need to see your actual configuration command and the results. Are you configuring as "--target=powerpc-mpc55xx" or "--target=powerpc-eabispe"?? You must configure from the top-level (i.e. you don't configure inside the newlib subdirectory; the top-level src configuration does that for you when you finally issue "make all" or "make all-target-newlib").
>
> -- Jeff J.
>
> Gerster Jochen-B01096 wrote:
>
>>I build the binutils and the gcc bootstrap using this manual
>>http://www.ifp.uiuc.edu/~nakazato/tips/xgcc.html
>>
>>
>>-----Original Message-----
>>From: newlib-owner@sourceware.org [mailto:newlib-owner@sourceware.org]
>>On Behalf Of Gerster Jochen-B01096
>>Sent: Freitag, 24. März 2006 11:17
>>To: newlib@sources.redhat.com
>>Subject: newlib didn't create makefiles
>>
>>Hi,
>>
>>I'm working on porting eCos to the powerpc mpc55xx family
>>
>>one step is building a gcc. And that's where the trouble getting
>>started
>>
>>USING:
>>binutils 2.15 < patch_e200z6_binutils-2.15.diff
>>gcc-3.4.3 < patch_all_e200_gcc-3.4.3.diff
>>newlib 1.12.0
>>
>>TARGET: powerpc mpc55xx
>>HOST: i686-pc-cygwin
>>BUILD: i686-pc-cygwin
>>
>>Building binutils 2.15 - works
>>Building gcc 3.4.3 bootstrap - works
>>now I want to build newlib and ...
>>
>>make[4]: Entering directory `/src/build-newlib/powerpc-eabispe/mpc7400/newlib'
>>make[4]: *** No rule to make target `all'. Stop.
>>make[4]: Leaving directory `/src/build-newlib/powerpc-eabispe/mpc7400/newlib'
>>make[3]: *** [multi-do] Error 1
>>make[3]: Leaving directory `/src/build-newlib/powerpc-eabispe/newlib'
>>make[2]: *** [all-multi] Error 2
>>make[2]: Leaving directory `/src/build-newlib/powerpc-eabispe/newlib'
>>make[1]: *** [all-recursive-am] Error 2
>>make[1]: Leaving directory `/src/build-newlib/powerpc-eabispe/newlib'
>>make: *** [all-target-newlib] Error 2
>>
>>the directory mpc7400/newlib is completely empty, no makefile, nothing
>>
>>Any ideas???
>>
>>I also tested newlib 1.13.0 newlib 1.14.0 -> same results
>>
>>Thank you for your help!
>>
>>Jochen
>
>
>
> ------------------------------------------------------------------------
>
> b01096@B01096-11 /src/build_newlib
> $ make all
> make[1]: Entering directory `/src/build_newlib'
> mkdir -p -- ./etc
> Configuring in ./etc
> creating cache ./config.cache
> checking for a BSD compatible install... /usr/bin/install -c
> updating cache ./config.cache
> creating ./config.status
> creating Makefile
> make[2]: Entering directory `/src/build_newlib/etc'
> for f in standards.info configure.info; do \
> if test -f ../../newlib-1.14.0/etc/`echo $f | sed -e 's/.info$/.texi/'
> `; then \
> if make "MAKEINFO=makeinfo --split-size=5000000 --split-size=5000000
> " $f; then \
> true; \
> else \
> exit 1; \
> fi; \
> fi; \
> done
> make[3]: Entering directory `/src/build_newlib/etc'
> makeinfo --split-size=5000000 --split-size=5000000 --no-split -I../../newlib-1.1
> 4.0/etc -o standards.info ../../newlib-1.14.0/etc/standards.texi
> ../../newlib-1.14.0/etc/standards.texi:1743: warning: @strong{Note...} produces
> a spurious cross-reference in Info; reword to avoid that.
> ../../newlib-1.14.0/etc/standards.texi:1858: warning: @strong{Note...} produces
> a spurious cross-reference in Info; reword to avoid that.
> make[3]: Leaving directory `/src/build_newlib/etc'
> make[3]: Entering directory `/src/build_newlib/etc'
> rm -f configdev.txt configbuild.txt
> cp ../../newlib-1.14.0/etc/configdev.tin configdev.txt
> cp ../../newlib-1.14.0/etc/configbuild.tin configbuild.txt
> makeinfo --split-size=5000000 --split-size=5000000 -I../../newlib-1.14.0/etc -o
> configure.info ../../newlib-1.14.0/etc/configure.texi
> rm -f configdev.txt configbuild.txt
> make[3]: Leaving directory `/src/build_newlib/etc'
> make[2]: Leaving directory `/src/build_newlib/etc'
> Checking multilib configuration for newlib...
> mkdir -p -- powerpc-eabi/newlib
> Configuring in powerpc-eabi/newlib
> creating cache ./config.cache
> checking for a BSD compatible install... /usr/bin/install -c
> checking whether build environment is sane... yes
> checking whether make sets ${MAKE}... yes
> checking for Cygwin environment... no
> checking for mingw32 environment... no
> checking host system type... powerpc-unknown-eabi
> checking target system type... powerpc-unknown-eabi
> checking build system type... i686-pc-cygwin
> checking for working aclocal-1.4... missing
> checking for working autoconf... missing
> checking for working automake-1.4... missing
> checking for working autoheader... missing
> checking for working makeinfo... found
> checking for gcc... powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -i
> system /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1
> .14.0/newlib/libc/include
> checking whether we are using GNU C... yes
> checking whether powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -isys
> tem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1.14
> .0/newlib/libc/include accepts -g... yes
> checking for -as... powerpc-eabi-as
> checking for -ar... powerpc-eabi-ar
> checking for -ranlib... powerpc-eabi-ranlib
> checking for a BSD compatible install... /usr/bin/install -c
> checking whether to enable maintainer-specific portions of Makefiles... no
> checking for .preinit_array/.init_array/.fini_array support... yes
> checking for array aliasing support... no
> updating cache ./config.cache
> creating ./config.status
> creating Makefile
> creating newlib.h
> Adding multilib support to Makefile in ../../../newlib-1.14.0/newlib
> multidirs=nof/ le/ und/ le/und/ nof/le/ nof/und/ nof/le/und/
> with_multisubdir=
> Running configure in multilib subdirs nof/ le/ und/ le/und/ nof/le/ nof/und/ nof
> /le/und/
> pwd: /src/build_newlib/powerpc-eabi/newlib
> Running configure in multilib subdir nof/
> pwd: /src/build_newlib/powerpc-eabi
> mkdir nof
> Running configure in multilib subdir le/
> pwd: /src/build_newlib/powerpc-eabi
> mkdir le
> Running configure in multilib subdir und/
> pwd: /src/build_newlib/powerpc-eabi
> mkdir und
> Running configure in multilib subdir le/und/
> pwd: /src/build_newlib/powerpc-eabi
> mkdir le/und
> Running configure in multilib subdir nof/le/
> pwd: /src/build_newlib/powerpc-eabi
> mkdir nof/le
> Running configure in multilib subdir nof/und/
> pwd: /src/build_newlib/powerpc-eabi
> mkdir nof/und
> Running configure in multilib subdir nof/le/und/
> pwd: /src/build_newlib/powerpc-eabi
> mkdir nof/le/und
> configuring in libc
> running /bin/sh ../../../../newlib-1.14.0/newlib/libc/configure --build=i686-pc
> -cygwin --host=powerpc-eabi --target=powerpc-eabi --with-newlib --enable-multili
> b --with-cross-host=i686-pc-cygwin --prefix=/usr/local/powerpc-eabi '--program-t
> ransform-name=s,^,powerpc-eabi-,; ' --with-target-subdir=powerpc-eabi --cache-fi
> le=.././config.cache --srcdir=../../../../newlib-1.14.0/newlib/libc
> loading cache .././config.cache
> checking for a BSD compatible install... ../
> checking whether build environment is sane... yes
> checking whether make sets ${MAKE}... (cached) yes
> checking for Cygwin environment... (cached) no
> checking for mingw32 environment... (cached) no
> checking host system type... powerpc-unknown-eabi
> checking target system type... powerpc-unknown-eabi
> checking build system type... i686-pc-cygwin
> checking for working aclocal-1.4... missing
> checking for working autoconf... missing
> checking for working automake-1.4... missing
> checking for working autoheader... missing
> checking for working makeinfo... found
> checking for gcc... (cached) powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/n
> ewlib/ -isystem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src
> /newlib-1.14.0/newlib/libc/include
> checking whether we are using GNU C... (cached) yes
> checking whether powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -isys
> tem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1.14
> .0/newlib/libc/include accepts -g... (cached) yes
> checking for -as... (cached) powerpc-eabi-as
> checking for -ar... (cached) powerpc-eabi-ar
> checking for -ranlib... (cached) powerpc-eabi-ranlib
> checking for a BSD compatible install... ../
> checking whether to enable maintainer-specific portions of Makefiles... no
> creating ./config.status
> creating Makefile
> creating argz/Makefile
> creating ctype/Makefile
> creating errno/Makefile
> creating locale/Makefile
> creating misc/Makefile
> creating reent/Makefile
> creating search/Makefile
> creating stdio/Makefile
> creating stdio64/Makefile
> creating stdlib/Makefile
> creating string/Makefile
> creating time/Makefile
> creating posix/Makefile
> creating signal/Makefile
> creating syscalls/Makefile
> creating unix/Makefile
> creating iconv/Makefile
> creating iconv/ces/Makefile
> creating iconv/ccs/Makefile
> creating iconv/ccs/binary/Makefile
> creating iconv/lib/Makefile
> configuring in machine
> running /bin/sh ../../../../../newlib-1.14.0/newlib/libc/machine/configure --bu
> ild=i686-pc-cygwin --host=powerpc-eabi --target=powerpc-eabi --with-newlib --ena
> ble-multilib --with-cross-host=i686-pc-cygwin --prefix=/usr/local/powerpc-eabi '
> --program-transform-name=s,^,powerpc-eabi-,; ' --with-target-subdir=powerpc-eabi
> --cache-file=../.././config.cache --srcdir=../../../../../newlib-1.14.0/newlib/
> libc/machine
> loading cache ../.././config.cache
> checking for a BSD compatible install... ../
> checking whether build environment is sane... yes
> checking whether make sets ${MAKE}... (cached) yes
> checking for Cygwin environment... (cached) no
> checking for mingw32 environment... (cached) no
> checking host system type... powerpc-unknown-eabi
> checking target system type... powerpc-unknown-eabi
> checking build system type... i686-pc-cygwin
> checking for working aclocal-1.4... missing
> checking for working autoconf... missing
> checking for working automake-1.4... missing
> checking for working autoheader... missing
> checking for working makeinfo... found
> checking for gcc... (cached) powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/n
> ewlib/ -isystem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src
> /newlib-1.14.0/newlib/libc/include
> checking whether we are using GNU C... (cached) yes
> checking whether powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -isys
> tem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1.14
> .0/newlib/libc/include accepts -g... (cached) yes
> checking for -as... (cached) powerpc-eabi-as
> checking for -ar... (cached) powerpc-eabi-ar
> checking for -ranlib... (cached) powerpc-eabi-ranlib
> checking for a BSD compatible install... ../
> checking whether to enable maintainer-specific portions of Makefiles... no
> creating ./config.status
> creating Makefile
> configuring in powerpc
> running /bin/sh ../../../../../../newlib-1.14.0/newlib/libc/machine/powerpc/conf
> igure --build=i686-pc-cygwin --host=powerpc-eabi --target=powerpc-eabi --with-n
> ewlib --enable-multilib --with-cross-host=i686-pc-cygwin --prefix=/usr/local/pow
> erpc-eabi '--program-transform-name=s,^,powerpc-eabi-,; ' --with-target-subdir=p
> owerpc-eabi --cache-file=../../.././config.cache --srcdir=../../../../../../newl
> ib-1.14.0/newlib/libc/machine/powerpc
> loading cache ../../.././config.cache
> checking for a BSD compatible install... ../
> checking whether build environment is sane... yes
> checking whether make sets ${MAKE}... (cached) yes
> checking for Cygwin environment... (cached) no
> checking for mingw32 environment... (cached) no
> checking host system type... powerpc-unknown-eabi
> checking target system type... powerpc-unknown-eabi
> checking build system type... i686-pc-cygwin
> checking for working aclocal-1.4... missing
> checking for working autoconf... missing
> checking for working automake-1.4... missing
> checking for working autoheader... missing
> checking for working makeinfo... found
> checking for gcc... (cached) powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/n
> ewlib/ -isystem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src
> /newlib-1.14.0/newlib/libc/include
> checking whether we are using GNU C... (cached) yes
> checking whether powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -isys
> tem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1.14
> .0/newlib/libc/include accepts -g... (cached) yes
> checking for -as... (cached) powerpc-eabi-as
> checking for -ar... (cached) powerpc-eabi-ar
> checking for -ranlib... (cached) powerpc-eabi-ranlib
> checking for a BSD compatible install... ../
> checking whether to enable maintainer-specific portions of Makefiles... no
> creating ./config.status
> creating Makefile
> configuring in sys
> running /bin/sh ../../../../../newlib-1.14.0/newlib/libc/sys/configure --build=
> i686-pc-cygwin --host=powerpc-eabi --target=powerpc-eabi --with-newlib --enable-
> multilib --with-cross-host=i686-pc-cygwin --prefix=/usr/local/powerpc-eabi '--pr
> ogram-transform-name=s,^,powerpc-eabi-,; ' --with-target-subdir=powerpc-eabi --c
> ache-file=../.././config.cache --srcdir=../../../../../newlib-1.14.0/newlib/libc
> /sys
> loading cache ../.././config.cache
> checking for a BSD compatible install... ../
> checking whether build environment is sane... yes
> checking whether make sets ${MAKE}... (cached) yes
> checking for Cygwin environment... (cached) no
> checking for mingw32 environment... (cached) no
> checking host system type... powerpc-unknown-eabi
> checking target system type... powerpc-unknown-eabi
> checking build system type... i686-pc-cygwin
> checking for working aclocal-1.4... missing
> checking for working autoconf... missing
> checking for working automake-1.4... missing
> checking for working autoheader... missing
> checking for working makeinfo... found
> checking for gcc... (cached) powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/n
> ewlib/ -isystem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src
> /newlib-1.14.0/newlib/libc/include
> checking whether we are using GNU C... (cached) yes
> checking whether powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -isys
> tem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1.14
> .0/newlib/libc/include accepts -g... (cached) yes
> checking for -as... (cached) powerpc-eabi-as
> checking for -ar... (cached) powerpc-eabi-ar
> checking for -ranlib... (cached) powerpc-eabi-ranlib
> checking for a BSD compatible install... ../
> checking whether to enable maintainer-specific portions of Makefiles... no
> creating ./config.status
> creating Makefile
> configuring in libm
> running /bin/sh ../../../../newlib-1.14.0/newlib/libm/configure --build=i686-pc
> -cygwin --host=powerpc-eabi --target=powerpc-eabi --with-newlib --enable-multili
> b --with-cross-host=i686-pc-cygwin --prefix=/usr/local/powerpc-eabi '--program-t
> ransform-name=s,^,powerpc-eabi-,; ' --with-target-subdir=powerpc-eabi --cache-fi
> le=.././config.cache --srcdir=../../../../newlib-1.14.0/newlib/libm
> loading cache .././config.cache
> checking for a BSD compatible install... ../
> checking whether build environment is sane... yes
> checking whether make sets ${MAKE}... (cached) yes
> checking for Cygwin environment... (cached) no
> checking for mingw32 environment... (cached) no
> checking host system type... powerpc-unknown-eabi
> checking target system type... powerpc-unknown-eabi
> checking build system type... i686-pc-cygwin
> checking for working aclocal-1.4... missing
> checking for working autoconf... missing
> checking for working automake-1.4... missing
> checking for working autoheader... missing
> checking for working makeinfo... found
> checking for gcc... (cached) powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/n
> ewlib/ -isystem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src
> /newlib-1.14.0/newlib/libc/include
> checking whether we are using GNU C... (cached) yes
> checking whether powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -isys
> tem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1.14
> .0/newlib/libc/include accepts -g... (cached) yes
> checking for -as... (cached) powerpc-eabi-as
> checking for -ar... (cached) powerpc-eabi-ar
> checking for -ranlib... (cached) powerpc-eabi-ranlib
> checking for a BSD compatible install... ../
> checking whether to enable maintainer-specific portions of Makefiles... no
> creating ./config.status
> creating Makefile
> creating math/Makefile
> creating mathfp/Makefile
> creating common/Makefile
> configuring in machine
> running /bin/sh ../../../../../newlib-1.14.0/newlib/libm/machine/configure --bu
> ild=i686-pc-cygwin --host=powerpc-eabi --target=powerpc-eabi --with-newlib --ena
> ble-multilib --with-cross-host=i686-pc-cygwin --prefix=/usr/local/powerpc-eabi '
> --program-transform-name=s,^,powerpc-eabi-,; ' --with-target-subdir=powerpc-eabi
> --cache-file=../.././config.cache --srcdir=../../../../../newlib-1.14.0/newlib/
> libm/machine
> loading cache ../.././config.cache
> checking for a BSD compatible install... ../
> checking whether build environment is sane... yes
> checking whether make sets ${MAKE}... (cached) yes
> checking for Cygwin environment... (cached) no
> checking for mingw32 environment... (cached) no
> checking host system type... powerpc-unknown-eabi
> checking target system type... powerpc-unknown-eabi
> checking build system type... i686-pc-cygwin
> checking for working aclocal-1.4... missing
> checking for working autoconf... missing
> checking for working automake-1.4... missing
> checking for working autoheader... missing
> checking for working makeinfo... found
> checking for gcc... (cached) powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/n
> ewlib/ -isystem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src
> /newlib-1.14.0/newlib/libc/include
> checking whether we are using GNU C... (cached) yes
> checking whether powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -isys
> tem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1.14
> .0/newlib/libc/include accepts -g... (cached) yes
> checking for -as... (cached) powerpc-eabi-as
> checking for -ar... (cached) powerpc-eabi-ar
> checking for -ranlib... (cached) powerpc-eabi-ranlib
> checking for a BSD compatible install... ../
> checking whether to enable maintainer-specific portions of Makefiles... no
> creating ./config.status
> creating Makefile
> configuring in doc
> running /bin/sh ../../../../newlib-1.14.0/newlib/doc/configure --build=i686-pc-
> cygwin --host=powerpc-eabi --target=powerpc-eabi --with-newlib --enable-multilib
> --with-cross-host=i686-pc-cygwin --prefix=/usr/local/powerpc-eabi '--program-tr
> ansform-name=s,^,powerpc-eabi-,; ' --with-target-subdir=powerpc-eabi --cache-fil
> e=.././config.cache --srcdir=../../../../newlib-1.14.0/newlib/doc
> loading cache .././config.cache
> checking for a BSD compatible install... ../
> checking whether build environment is sane... yes
> checking whether make sets ${MAKE}... (cached) yes
> checking for Cygwin environment... (cached) no
> checking for mingw32 environment... (cached) no
> checking host system type... powerpc-unknown-eabi
> checking target system type... powerpc-unknown-eabi
> checking build system type... i686-pc-cygwin
> checking for working aclocal-1.4... missing
> checking for working autoconf... missing
> checking for working automake-1.4... missing
> checking for working autoheader... missing
> checking for working makeinfo... found
> checking for gcc... (cached) powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/n
> ewlib/ -isystem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src
> /newlib-1.14.0/newlib/libc/include
> checking whether we are using GNU C... (cached) yes
> checking whether powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -isys
> tem /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1.14
> .0/newlib/libc/include accepts -g... (cached) yes
> checking for -as... (cached) powerpc-eabi-as
> checking for -ar... (cached) powerpc-eabi-ar
> checking for -ranlib... (cached) powerpc-eabi-ranlib
> checking for a BSD compatible install... ../
> checking whether to enable maintainer-specific portions of Makefiles... no
> checking for build system executable suffix... no
> updating cache .././config.cache
> creating ./config.status
> creating Makefile
> make[2]: Entering directory `/src/build_newlib/powerpc-eabi/newlib'
> make "AR_FLAGS=rc" "CC_FOR_BUILD=gcc" "CFLAGS=-O2 -g -O2 " "CFLAGS_
> FOR_BUILD=-g -O2 " "CFLAGS_FOR_TARGET=-O2 -g -O2 " "LDFLAGS=" "LIBC
> FLAGS=-O2 -g -O2 " "LIBCFLAGS_FOR_TARGET=-O2 -g -O2 " "MAKE=make" "MAK
> EINFO=makeinfo --split-size=5000000 --split-size=5000000 " "PICFLAG=" "PICF
> LAG_FOR_TARGET=" "SHELL=/bin/sh" "EXPECT=expect" "RUNTEST
> =runtest" "RUNTESTFLAGS=" "exec_prefix=/usr/local/powerpc-eabi" "i
> nfodir=/usr/local/powerpc-eabi/info" "libdir=/usr/local/powerpc-eabi/lib" "pr
> efix=/usr/local/powerpc-eabi" "tooldir=/usr/local/powerpc-eabi/powerpc-eabi" "
> top_toollibdir=/usr/local/powerpc-eabi/powerpc-eabi/lib" "AR=powerpc-eabi
> -ar" "AS=powerpc-eabi-as" "CC=powerpc-eabi-gcc -B/src/build_newlib/powerpc
> -eabi/newlib/ -isystem /src/build_newlib/powerpc-eabi/newlib/targ-include -isyst
> em /src/newlib-1.14.0/newlib/libc/include" "LD=powerpc-eabi-ld" "LIBCFLA
> GS=-O2 -g -O2 " "NM=powerpc-eabi-nm" "PICFLAG=" "RANLIB=powerpc-
> eabi-ranlib" "DESTDIR=" all-recursive
> make[3]: Entering directory `/src/build_newlib/powerpc-eabi/newlib'
> make "AR_FLAGS=rc" "CC_FOR_BUILD=gcc" "CFLAGS=-O2 -g -O2 " "CFLAGS_
> FOR_BUILD=-g -O2 " "CFLAGS_FOR_TARGET=-O2 -g -O2 " "LDFLAGS=" "LIBC
> FLAGS=-O2 -g -O2 " "LIBCFLAGS_FOR_TARGET=-O2 -g -O2 " "MAKE=make" "MAK
> EINFO=makeinfo --split-size=5000000 --split-size=5000000 " "PICFLAG=" "PICF
> LAG_FOR_TARGET=" "SHELL=/bin/sh" "EXPECT=expect" "RUNTEST
> =runtest" "RUNTESTFLAGS=" "exec_prefix=/usr/local/powerpc-eabi" "i
> nfodir=/usr/local/powerpc-eabi/info" "libdir=/usr/local/powerpc-eabi/lib" "pr
> efix=/usr/local/powerpc-eabi" "tooldir=/usr/local/powerpc-eabi/powerpc-eabi" "
> top_toollibdir=/usr/local/powerpc-eabi/powerpc-eabi/lib" "AR=powerpc-eabi
> -ar" "AS=powerpc-eabi-as" "CC=powerpc-eabi-gcc -B/src/build_newlib/powerpc
> -eabi/newlib/ -isystem /src/build_newlib/powerpc-eabi/newlib/targ-include -isyst
> em /src/newlib-1.14.0/newlib/libc/include" "LD=powerpc-eabi-ld" "LIBCFLA
> GS=-O2 -g -O2 " "NM=powerpc-eabi-nm" "PICFLAG=" "RANLIB=powerpc-
> eabi-ranlib" "DESTDIR=" DO=all multi-do # make
> make[4]: Entering directory `/src/build_newlib/powerpc-eabi/newlib'
> if [ -z "nof/ le/ und/ le/und/ nof/le/ nof/und/ nof/le/und/" ]; then \
> true; \
> else \
> rootpre=`${PWDCMD-pwd}`/; export rootpre; \
> srcrootpre=`cd ../../../newlib-1.14.0/newlib; ${PWDCMD-pwd}`/; export
> srcrootpre; \
> lib=`echo ${rootpre} | sed -e 's,^.*/\([^/][^/]*\)/$,\1,'`; \
> compiler="powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -i
> system /src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1
> .14.0/newlib/libc/include"; \
> for i in `${compiler} --print-multi-lib 2>/dev/null`; do \
> dir=`echo $i | sed -e 's/;.*$//'`; \
> if [ "${dir}" = "." ]; then \
> true; \
> else \
> if [ -d ../${dir}/${lib} ]; then \
> flags=`echo $i | sed -e 's/^[^;]*;//' -e 's/@/ -/g'`; \
> if (cd ../${dir}/${lib}; make "AR_FLAGS=rc" "CC_FOR_BUILD=gc
> c" "CFLAGS=-O2 -g -O2 " "CFLAGS_FOR_BUILD=-g -O2 " "CFLAGS_FOR_TARG
> ET=-O2 -g -O2 " "LDFLAGS=" "LIBCFLAGS=-O2 -g -O2 " "LIBCFLA
> GS_FOR_TARGET=-O2 -g -O2 " "MAKE=make" "MAKEINFO=makeinfo --split-size=
> 5000000 --split-size=5000000 " "PICFLAG=" "PICFLAG_FOR_TARGET=" "S
> HELL=/bin/sh" "EXPECT=expect" "RUNTEST=runtest" "RUNTESTFLAGS="
> "exec_prefix=/usr/local/powerpc-eabi" "infodir=/usr/local/powerpc-eabi
> /info" "libdir=/usr/local/powerpc-eabi/lib" "prefix=/usr/local/powerpc-eabi"
> "tooldir=/usr/local/powerpc-eabi/powerpc-eabi" "top_toollibdir=/usr/loc
> al/powerpc-eabi/powerpc-eabi/lib" "AR=powerpc-eabi-ar" "AS=powerpc-eabi
> -as" "CC=powerpc-eabi-gcc -B/src/build_newlib/powerpc-eabi/newlib/ -isystem /
> src/build_newlib/powerpc-eabi/newlib/targ-include -isystem /src/newlib-1.14.0/ne
> wlib/libc/include" "LD=powerpc-eabi-ld" "LIBCFLAGS=-O2 -g -O2 " "NM=pow
> erpc-eabi-nm" "PICFLAG=" "RANLIB=powerpc-eabi-ranlib" "DESTDIR=" \
> CFLAGS="-O2 -g -O2 ${flags}" \
> FCFLAGS=" ${flags}" \
> FFLAGS=" ${flags}" \
> ADAFLAGS=" ${flags}" \
> prefix="/usr/local/powerpc-eabi" \
> exec_prefix="/usr/local/powerpc-eabi" \
> GCJFLAGS="@GCJFLAGS@ ${flags}" \
> CXXFLAGS="-g -O2 ${flags}" \
> LIBCFLAGS="-O2 -g -O2 ${flags}" \
> LIBCXXFLAGS="-g -O2 -fno-implicit-templates ${f
> lags}" \
> LDFLAGS=" ${flags}" \
> MULTIFLAGS="${flags}" \
> DESTDIR="" \
> INSTALL="/usr/bin/install -c" \
> INSTALL_DATA="/usr/bin/install -c -m 644" \
> INSTALL_PROGRAM="/usr/bin/install -c " \
> INSTALL_SCRIPT="/usr/bin/install -c" \
> all); then \
> true; \
> else \
> exit 1; \
> fi; \
> else true; \
> fi; \
> fi; \
> done; \
> fi
> make[5]: Entering directory `/src/build_newlib/powerpc-eabi/nof/newlib'
> make[5]: *** No rule to make target `all'. Stop.
> make[5]: Leaving directory `/src/build_newlib/powerpc-eabi/nof/newlib'
> make[4]: *** [multi-do] Error 1
> make[4]: Leaving directory `/src/build_newlib/powerpc-eabi/newlib'
> make[3]: *** [all-multi] Error 2
> make[3]: Leaving directory `/src/build_newlib/powerpc-eabi/newlib'
> make[2]: *** [all-recursive-am] Error 2
> make[2]: Leaving directory `/src/build_newlib/powerpc-eabi/newlib'
> make[1]: *** [all-target-newlib] Error 2
> make[1]: Leaving directory `/src/build_newlib'
> make: *** [all] Error 2
>
> b01096@B01096-11 /src/build_newlib
> $
>
>
> ------------------------------------------------------------------------
>
> b01096@B01096-11 /src/build_newlib
> $ ../newlib-1.14.0/configure --target=powerpc-eabi --prefix=/usr/local/powerpc-
> eabi
> creating cache ./config.cache
> checking host system type... i686-pc-cygwin
> checking target system type... powerpc-unknown-eabi
> checking build system type... i686-pc-cygwin
> checking for a BSD compatible install... /usr/bin/install -c
> checking whether ln works... yes
> checking whether ln -s works... yes
> checking for gcc... gcc
> checking whether the C compiler (gcc ) works... yes
> checking whether the C compiler (gcc ) is a cross-compiler... no
> checking whether we are using GNU C... yes
> checking whether gcc accepts -g... yes
> checking for gnatbind... no
> checking whether compiler driver understands Ada... no
> checking how to compare bootstrapped objects... cmp --ignore-initial=16 $$f1 $$f
> 2
> checking for correct version of gmp.h... no
> checking for bison... bison -y
> checking for bison... bison
> checking for gm4... no
> checking for gnum4... no
> checking for m4... m4
> checking for flex... flex
> checking for flex... flex
> checking for makeinfo... makeinfo
> checking for expect... no
> checking for runtest... no
> checking for i686-pc-cygwin-ar... no
> checking for ar... ar
> checking for i686-pc-cygwin-as... no
> checking for as... as
> checking for i686-pc-cygwin-dlltool... no
> checking for dlltool... dlltool
> checking for i686-pc-cygwin-ld... /usr/lib/gcc/i686-pc-cygwin/3.4.4/../../../../
> i686-pc-cygwin/bin/ld.exe
> checking for i686-pc-cygwin-lipo... no
> checking for lipo... no
> checking for i686-pc-cygwin-nm... no
> checking for nm... nm
> checking for i686-pc-cygwin-ranlib... no
> checking for ranlib... ranlib
> checking for i686-pc-cygwin-strip... no
> checking for strip... strip
> checking for i686-pc-cygwin-windres... no
> checking for windres... windres
> checking for i686-pc-cygwin-objcopy... no
> checking for objcopy... objcopy
> checking for i686-pc-cygwin-objdump... no
> checking for objdump... objdump
> checking for powerpc-eabi-ar... powerpc-eabi-ar
> checking for powerpc-eabi-as... powerpc-eabi-as
> checking for powerpc-eabi-cc... no
> checking for powerpc-eabi-gcc... powerpc-eabi-gcc
> checking for powerpc-eabi-c++... powerpc-eabi-c++
> checking for powerpc-eabi-dlltool... no
> checking for powerpc-eabi-gcc... powerpc-eabi-gcc
> checking for powerpc-eabi-gcj... powerpc-eabi-gcj
> checking for powerpc-eabi-gfortran... no
> checking for powerpc-eabi-ld... powerpc-eabi-ld
> checking for powerpc-eabi-lipo... no
> checking for powerpc-eabi-nm... powerpc-eabi-nm
> checking for powerpc-eabi-objdump... powerpc-eabi-objdump
> checking for powerpc-eabi-ranlib... powerpc-eabi-ranlib
> checking for powerpc-eabi-strip... powerpc-eabi-strip
> checking for powerpc-eabi-windres... no
> checking where to find the target ar... pre-installed
> checking where to find the target as... pre-installed
> checking where to find the target cc... pre-installed
> checking where to find the target c++... pre-installed
> checking where to find the target c++ for libstdc++... pre-installed
> checking where to find the target dlltool... pre-installed
> checking where to find the target gcc... pre-installed
> checking where to find the target gcj... pre-installed
> checking where to find the target gfortran... pre-installed
> checking where to find the target ld... pre-installed
> checking where to find the target lipo... pre-installed
> checking where to find the target nm... pre-installed
> checking where to find the target objdump... pre-installed
> checking where to find the target ranlib... pre-installed
> checking where to find the target strip... pre-installed
> checking where to find the target windres... pre-installed
> checking whether to enable maintainer-specific portions of Makefiles... no
> checking if symbolic links between directories work... yes
> updating cache ./config.cache
> creating ./config.status
> creating Makefile
More information about the Newlib
mailing list