MIPS o32 ABI spec, $fp1 valid?

[Andrew Cagney]

> Andrew Cagney <ac131313@redhat.com> writes:
> 
>>Does the o32 ABI specify how to spill a loating point register (a spill 
>>is different to a double store of a parameter as a spilt register is 
>>recovered by the unwind code.  mdebug might, for instance, specify 
>>something.
> 
> 
> No, mdebug says nothing about how spills are done (it says nothing
> about how exactly float/double are stored, AFAICT).

Sigh.  However, this code is finally starting to make [partial] sense.

> The hardware requires mentioning the odd regs to get the entire
> 64 bits stored.  In MIPS1.
> 
> Here is some mips1 o32 disassembly output, IRIX, so big-endian:
> Given 

> double x1(double d)
> {
>         double d2 = d + 3.0;
>         d2 += x2(5.0);
>         return d2/4.5;
> }

The param

> [  11] 0x  58:  e7 ad 00 38    swc1 $f13,56($sp)
> [  11] 0x  5c:  e7 ac 00 3c    swc1 $f12,60($sp)

The spill

> [  11] 0x  90:  e7 b5 00 18    swc1 $f21,24($sp)
> [  11] 0x  94:  e7 b4 00 1c    swc1 $f20,28($sp)
> [  12] 0x  98:  e7 a8 00 34    swc1 $f8,52($sp)
> [  13] 0x  9c:  03 20 f8 09    jalr $25
> [  12] 0x  a0:  e7 a9 00 30    swc1 $f9,48($sp)


>  #   9  }
>  #  10  double x1(double d)
>  #  11  {
>         .ent    x1 2
> x1:
>         .option O1
>         .set     noreorder
>         .cpload $25
>         .set     reorder
>         subu    $sp, 56
>         sw      $31, 36($sp)
>         .cprestore      32
>         s.d     $f12, 56($sp)
>         s.d     $f20, 24($sp)
>         .mask   0x90000000, -20
>         .fmask  0x00300000, -32
>         .frame  $sp, 56, $31
>         .loc    2 11
> ...
> 
> Now I must admit I am using a modern compiler, not an original
> old mips1 compiler. So while the spill would be the same, 
> (and same as reg saves) I don't recall precisely how it would
> really look in IRIX mips1 assembler.

Ref: mips_find_saved_regs /float_mask/ at the end of the function.
I believe that the debug info indicates that $f20/$f21 were both saved. 
  The code comes with the comment:

     /* Apparently, the freg_offset gives the offset to the first 64
        bit saved.

        When the ABI specifies 64 bit saved registers, the FREG_OFFSET
        designates the first saved 64 bit register.

        When the ABI specifies 32 bit saved registers, the ``64 bit
        saved DOUBLE'' consists of two adjacent 32 bit registers, Hence
        FREG_OFFSET, designates the address of the lower register of
        the register pair.  Adjust the offset so that it designates the
        upper register of the pair -- i.e., the address of the first
        saved 32 bit register.  */

Now, from the thread so far, it is clear that the comment is only 
partially correct.  It should indicate that:

On a big endian 32 bit ABI, the compiler spills floating-point registers 
as a pair and as a floating-point double.  Because the target is 
big-endian, this leads to the register pair being stored in reverse 
order vis: $fN ||| $fN+1 are stored as $fN+1 and then $fN.

The code doesn't do that, it gets the address of $fN correct, but $fN+1 
is 8 bytes out.  Outch!

Given o32, GDB needs to track the location of the individual 32 bit 
floating point registers and not 64 bit FP pairs.  By doing that, the 
code (mips_register_to_value):

   frame_read_register (frame, regnum + 0, (char *) to + 4);
   frame_read_register (frame, regnum + 1, (char *) to + 0);

is able to correctly construct a double value for any frame.

Andrew

(dave, one last favour, can you check -o32 -mips>1 to see if the fmask 
remains the same.  I'd expect it to).