[RFA] mips-tdep.c small cleanup

[Joel Brobecker]

I removed some dead code, did some reformatting, and also did one little
code factoring, to make the code look prettier. That's actually the last
part of the change that made me choose a RFA rather than a PATCH. It
looks obvious, and tests ok, but I'd appreciate a second pair of eyes
looking at the change too.

The idea is to clean this code up a little bit, so I can see better
how to implement Andrew's suggestion re- inlining.

2004-09-01  Joel Brobecker  <brobecker@gnat.com>

        * mips-tdep.c (mips_insn32_frame_cache): Remove some dead code.
        Minor reformatting. Some code factoring.

tested on mips-irix 6.5.
OK to apply?

Thanks,
-- 
Joel
-------------- next part --------------
--- mips-tdep.c.new_ref	2004-09-01 17:38:33.996866250 -0400
+++ mips-tdep.c	2004-09-01 18:27:47.336020442 -0400
@@ -2118,28 +2118,16 @@ mips_insn32_frame_cache (struct frame_in
       /* Bitmasks; set if we have found a save for the register.  */
       unsigned long gen_save_found = 0;
       unsigned long float_save_found = 0;
-      int mips16;
 
-      /* If the address is odd, assume this is MIPS16 code.  */
       addr = PROC_LOW_ADDR (proc_desc);
-      mips16 = pc_is_mips16 (addr);
 
       /* Scan through this function's instructions preceding the
          current PC, and look for those that save registers.  */
       while (addr < frame_pc_unwind (next_frame))
 	{
-	  if (mips16)
-	    {
-	      mips16_decode_reg_save (mips16_fetch_instruction (addr),
-				      &gen_save_found);
-	      addr += MIPS16_INSTLEN;
-	    }
-	  else
-	    {
-	      mips32_decode_reg_save (mips32_fetch_instruction (addr),
-				      &gen_save_found, &float_save_found);
-	      addr += MIPS_INSTLEN;
-	    }
+          mips32_decode_reg_save (mips32_fetch_instruction (addr),
+                                  &gen_save_found, &float_save_found);
+          addr += MIPS_INSTLEN;
 	}
       gen_mask = gen_save_found;
       float_mask = float_save_found;
@@ -2159,48 +2147,20 @@ mips_insn32_frame_cache (struct frame_in
 	}
   }
 
-  /* The MIPS16 entry instruction saves $s0 and $s1 in the reverse
-     order of that normally used by gcc.  Therefore, we have to fetch
-     the first instruction of the function, and if it's an entry
-     instruction that saves $s0 or $s1, correct their saved addresses.  */
-  if (pc_is_mips16 (PROC_LOW_ADDR (proc_desc)))
-    {
-      ULONGEST inst = mips16_fetch_instruction (PROC_LOW_ADDR (proc_desc));
-      if ((inst & 0xf81f) == 0xe809 && (inst & 0x700) != 0x700)
-	/* entry */
-	{
-	  int reg;
-	  int sreg_count = (inst >> 6) & 3;
-
-	  /* Check if the ra register was pushed on the stack.  */
-	  CORE_ADDR reg_position = (cache->base
-				    + PROC_REG_OFFSET (proc_desc));
-	  if (inst & 0x20)
-	    reg_position -= mips_abi_regsize (gdbarch);
-
-	  /* Check if the s0 and s1 registers were pushed on the
-	     stack.  */
-	  /* NOTE: cagney/2004-02-08: Huh?  This is doing no such
-             check.  */
-	  for (reg = 16; reg < sreg_count + 16; reg++)
-	    {
-	      cache->saved_regs[NUM_REGS + reg].addr = reg_position;
-	      reg_position -= mips_abi_regsize (gdbarch);
-	    }
-	}
-    }
-
   /* Fill in the offsets for the registers which float_mask says were
      saved.  */
   {
-    CORE_ADDR reg_position = (cache->base
-			      + PROC_FREG_OFFSET (proc_desc));
+    CORE_ADDR reg_position = (cache->base + PROC_FREG_OFFSET (proc_desc));
     int ireg;
+
     /* Fill in the offsets for the float registers which float_mask
        says were saved.  */
     for (ireg = MIPS_NUMREGS - 1; float_mask; --ireg, float_mask <<= 1)
       if (float_mask & 0x80000000)
 	{
+          const int regno =
+            NUM_REGS + mips_regnum (current_gdbarch)->fp0 + ireg;
+
 	  if (mips_abi_regsize (gdbarch) == 4
 	      && TARGET_BYTE_ORDER == BFD_ENDIAN_BIG)
 	    {
@@ -2227,15 +2187,14 @@ mips_insn32_frame_cache (struct frame_in
 	         reg_position is decremented each time through the
 	         loop).  */
 	      if ((ireg & 1))
-		cache->saved_regs[NUM_REGS + mips_regnum (current_gdbarch)->fp0 + ireg]
-		  .addr = reg_position - mips_abi_regsize (gdbarch);
+		cache->saved_regs[regno].addr =
+                  reg_position - mips_abi_regsize (gdbarch);
 	      else
-		cache->saved_regs[NUM_REGS + mips_regnum (current_gdbarch)->fp0 + ireg]
-		  .addr = reg_position + mips_abi_regsize (gdbarch);
+		cache->saved_regs[regno].addr =
+                 reg_position + mips_abi_regsize (gdbarch);
 	    }
 	  else
-	    cache->saved_regs[NUM_REGS + mips_regnum (current_gdbarch)->fp0 + ireg]
-	      .addr = reg_position;
+	    cache->saved_regs[regno].addr = reg_position;
 	  reg_position -= mips_abi_regsize (gdbarch);
 	}