[ECOS] Trouble with eCos Config Tool

[Andy Jackson]

Hi Ray/Tom,

Another option is to get the latest CVS sources and apply the patches on our 
web site (www.xylanta.com), then compile with wxWidgets 2.6.3 rather than 
the older 2.4.2 and see if that improves matters. I can send my build 
scripts should you need them.

Alternatively there are binaries on the web site as well.

    Andy..

----- Original Message ----- 
From: "Ray Duran" <Ray.Duran@FutureElectronics.com>
To: <ecos-discuss@ecos.sourceware.org>
Sent: Friday, September 29, 2006 12:30 AM
Subject: RE: [ECOS] Trouble with eCos Config Tool


Thanks for your reply Tom.

I was able to download the same file as you: "configtool-060710.exe"
from
http://www.ecoscentric.com/devzone/configtool.shtml

However, following the rest of the instructions on building wxwidget( in
order to ultimately rebuild eCos config) I am having a problem with.
I see some strange make errors. In fact they are the same errors found
by another:
http://sourceware.org/ml/ecos-discuss/2006-06/msg00061.html There was no
posted reply to this e-mail.

How where you able to rebuild the eCos config tool?

Thanks,

-Ray


-----Original Message-----
From: Tom Malcolmson [mailto:Tom@Malcolmson.com]
Sent: Thursday, September 28, 2006 2:53 PM
To: Ray Duran
Cc: ecos-discuss@ecos.sourceware.org
Subject: Re: [ECOS] Trouble with eCos Config Tool


Ray,

I too have recently started with eCos.  I tried running configtool on
cygwin but it did not work.  Like you, I looked into it and found that
this is apparently a problem with newer versions of cygwin.

In the end, I found the page that you referenced, and downloaded the
updated tool on this page.  I think this is called
"configtool-060710.exe".  This works for me.
http://www.ecoscentric.com/devzone/configtool.shtml

I take it that, though the above web page says that configtool is a
wxWidgets app, it is only partially so and still relies on unix calls
for which it needs cygwin.

Tom.

Ray Duran wrote:
> Hello,
>
> I am a new to the eCos community.
>
> I followed the commands on the eCos webpage
>
> wget --passive-ftp ftp://ecos.sourceware.org/pub/ecos/ecos-install.tcl
>
> Then invoked installation tool
>
> sh ecos-install.tcl
>
> I followed the commands but did NOT select pre-built GNU toolchain as
I
> had already
> Downloaded a pre-built GNU ARM toolchain.
>
> After selecting a mirror-site everything seemed fine and I got a
> installation complete message.
>
> So, I thought my next step was to launch the configtool by invoking
> configtool.exe, but nothing happens.
>
> I did a little research on the mailing list and saw some sort of
related
> problems that say building the
> Config tool is "tricky" and that there are known problems when running
> against Cygwin 1.5.10 or later( which
> applies to me). What am I missing? The procedure outline in the link
> http://www.ecoscentric.com/devzone/configtool.shtml
> seems to reference the CVS version. Is there a problem invoking the
> Config tool with the non-CVS release?
>
> Any help or tips greatly appreciated,
>
> Regards,
>
> -Ray
>
> Ray Duran
> Altera Design Specialist
> Future Electronics
> 2220 O'Toole Avenue
> San Jose Ca. 95131
> 408 232 1478
> ray.duran@futureelectronics.com
>
> The information in this transmission contains information that is
> confidential and is intended only for the use of the individual or
> entity to whom it is addressed. If the reader of this message is not
the
> intended recipient please delete it and immediately notify the sender.

>
> If the purpose of this transmission is to provide a quotation or to
> confirm or acknowledge an order or to provide information in relation
to
> the Products and Services offered, unless otherwise agreed in writing,
> the FUTURE ELECTRONICS TERMS AND CONDITIONS OF SALE exclusively govern
> the sale of Products and the provision of services by Future
Electronics
> Inc. and its divisions, subsidiaries and affiliates and take
precedence
> over supplemental or conflicting terms and conditions to which notice
of
> objection is hereby given. The FUTURE ELECTRONICS TERMS AND CONDITIONS
> OF SALE are available at www.futureelectronics.com and may be provided
> on invoices, packing slips, order acknowledgements or other method.
>
>
>
>
>
>
>

-- 
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss


-- 
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss