[ECOS] HELP Unable to ping the device
Mukund JB.
mukundjb@esntechnologies.co.in
Wed Mar 2 12:58:00 GMT 2005
Hi gary,
> On Wed, 2005-03-02 at 17:05 +0530, Mukund JB. wrote:
> > Hello Gary,
> >
> > The network problem at redboot persists.
> >
> > > > Hello all,
> > > >
> > > > Sorry, the previuus mailwas with a wrong subject.
> > >
> > > Yup :-(
> > >
> > > > I am working on cirrus logic BSP & using EBD19312 board. I am
unable
> > to
> > > > ping the device.
> > > >
> > > > I am able to see the redboot prompt on my minicom. As I don't
have a
> > > > BOOTP on my network(cross cabled), I have configured the IP
using
> > > > ip_address command of redboot.
> > > >
> > > > The steps I followed are
> > > > 1) Connected to the host through cross cable (Host running tftp
> > server).
> > > > 2) D/W the Redboot using serial cable.
> > > > 3) executed the following command successfully
> > > > fis init -f
> > > > fconfig -i
> > > > ip_address -l 100.100.100.43 -h 100.100.100.13 ( NO
DHCPd/
> > > > BOOTp)
> > > >
> > > > After that, when I ping to HOST(100.100.100.13), it returns
TIMED
> > OUT.
> > > >
> > > > I am using a Intel 82557/8/9 ( cat/proc/pci entry shown card). I
am
> > not
> > > > able to guess the problem.
> > >
> > > How did you configure the port on your host computer?
> >
> > Baud rate = 57600 8N1
> > Hardware Flow control = NO
> > Serial device = dev/ttyS0
>
> We need to know how you configured the network card in your host?
> Have you tested the network using that card?
That is done by the sysadmin. However the card is working.
If I just tested it using ping 100.100.100.100 (DHCP server) it works
fine/responds.
Just excuse. I thought, when it comes to network, my HOST network card
will never come into picture. Can u just explain me how is the network
card on the HOST related?
> >
> > > Have you tried any debugging techniques?
> > > * Turn on network debug in RedBoot (requires reboot to become
> > effective)
> >
> > Sorry, I did not do that. How do I turn on the network debug in
redboot?
> > However, I get some message when I start the board after the redboot
is
> > loaded.
>
> Have you read the manual? Try the 'fconfig' command
whn I see the redboot promt I tried it as follows:-
fis init -f
fconfig -i
which asks me a set of questions like
Scripts yes/no
DNS address
MAC Address ------- why does it need this? How do I know the
exact MAC?
Then I set the ip_address of the machine using ip_address command.
ip_address -l 100.100.100.103 -h 100.100.100.43
100.100.100.103 --- Local IP address
100.100.100.43 --- IP address of Default server (HOST)
> >
> > > * Watch the "wire" from Linux (ethereal or tcpdump)
> > I watched it. I watched through ethereal what are the packets that
the
> > device is sending after installing redboot & restarting it.
> > It is sending nothing.
> >
> > I am less into ethereal stuff. I just doubt, Is the ethereal capable
of
> > capturing the bootp request patkets on the network. Just becos the
> > fields on the ethereal display are
> >
> > Time Source destination xxx xx
> >
> > & if the board is sending some BOOTP packets how will the ethereal
> > display them on the screen. I just doubt as there is no IP assigned
yet
> > to the board we are using.
>
> 'ethereal' can see and display any network traffic that your host
> computer can see. It will be able to display BOOTP packets, as
> well as any other packets exchanged between your target and host.
OK.
Where might be the problem? Guide me, please.
Regards,
Mukund jampala
>
> --
> ------------------------------------------------------------
> Gary Thomas | Consulting for the
> MLB Associates | Embedded world
> ------------------------------------------------------------
--
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss
More information about the Ecos-discuss
mailing list