[ECOS] 答复: [ECOS] Suggestion needed for the support of ecos for my philips ARM board

Zhang.Sonys@INVENTEC-inc.com Zhang.Sonys@INVENTEC-inc.com
Mon Aug 2 07:56:00 GMT 2004


Why not try run RedBoot in Flash? You can load the eCos + Application with http/tftp or X-modem/Y-modem protocol into RAM.

Brs
Sonys
 

-----原始邮件-----
发件人: Puneet [mailto:puneetgoel77@yahoo.co.uk]
发送时间: 2004年8月2日 13:35
收件人: ecos-discuss@ecos.sourceware.org
主题: Re: [ECOS] Suggestion needed for the support of ecos for my philips ARM board


one small doubt.

I am able to get one more ARM9 board with 256KB Flash and 128MB RAM.

will that work?

soppose i have an OS+Application with the image size of 1MB, where is that
stored? In Flash?

RAM comes in picture only when i need to run the OS?

am i right?

regards,
Puneet

----- Original Message ----- 
From: "Robert Cragie" <rcc@jennic.com>
To: "Puneet Goel" <puneetgoel77@yahoo.co.uk>
Sent: Friday, July 30, 2004 2:16 PM
Subject: RE: [ECOS] Suggestion needed for the support of ecos for my philips
ARM board


> If it is not listed here, it won't be supported:
>
> http://ecos.sourceware.org/hardware.html
>
> However, I would say a good starting point would be the HAL for the the
ARM
> PID, ARM AEB or ARM Evaluator E7T, as these all use chips based on the
> ARM7TDMI. Anthony Massa's book (available online here
> http://www.informit.com/content/downloads/perens/0130354732.pdf) has a
> section on porting.
>
> HTH
>
> Robert Cragie, Design Engineer
> _______________________________________________________________
> Jennic Ltd, Furnival Street, Sheffield, S1 4QT,  UK
> http://www.jennic.com  Tel: +44 (0) 114 281 2655
> _______________________________________________________________
>
> > -----Original Message-----
> > From: ecos-discuss-owner@ecos.sourceware.org
> > [mailto:ecos-discuss-owner@ecos.sourceware.org]On Behalf Of Puneet Goel
> > Sent: 29 July 2004 09:43
> > To: ecos-discuss@ecos.sourceware.org
> > Subject: [ECOS] Suggestion needed for the support of ecos for my philips
> > ARM board
> >
> >
> > Hi all,
> >
> > I am new to embedded linux and wiling to learn it. I
> > have a board Philips LPC2119/LPC2129 with 16/32 bit
> > ARM7TDMI-S core. Can you please let me know ecos
> > supports this board or not.
> >
> > http://www.semiconductors.philips.com/pip/LPC2119FBD64.html
> >
> >
> > regards,
> > Puneet
> >
> >
> >
> >
> >
> >
> > ___________________________________________________________ALL-NEW
> >  Yahoo! Messenger - all new features - even more fun!
> > http://uk.messenger.yahoo.com
> >
> > --
> > Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
> > and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss
> >
> >
>


-- 
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss


More information about the Ecos-discuss mailing list