[ECOS] gdb remote debug problem

Weilong Li wli@mtu.edu
Thu Apr 26 00:59:00 GMT 2001


Elf, thanks a lot for help.

I just discovered the problem. The target machine is so old that its serial
port
is rusted, and I tried anoter target, it is working.

Weilong

elf@florence.buici.com wrote:

> I've done exactly the same thing with success. I encountered some odd
> behavior when I didn't use exactly the software versions recommended
> by the eCos team.  I used:
>
>   binutils-2.11.90.0.1
>   gcc-core-2.95.2
>   gcc-g++-2.95.2
>   insight-5.0
>
> though the behavior you describe seems to indicate that the tools are
> correctly built.
>
> The most important thing to check is that your serial connection is
> correct.  It is worthwhile to use minicom (or a similar package) to
> test the physical, serial link.
>
>  -*-
>
> [deletia]
>
> > 3) Then I used the floppy disk to boot another computer, it is
> > intel 486 machine, I connected it with my intel redhat 7.0 machine using
> >
> > a null modem cable. I saw the following things show on intel 486
> > machine:
> >
> > ++$T0508:a4370000;04:e00f0000;#19++$T0508:a43700019
> >
> > So it seems the gdb stub on my target machine is working.
> > Then on intel redhat 7.0 machine, under directory
> > /opt/ecos/ecos-1.3.1/examples,
> > I typed i386-elf-gdb -nw hello, then the following shows:
> >
> > GNU gdb 5.0
> > Copyright 2000 Free Software Foundation, Inc.
> > GDB is free software, covered by the GNU General Public License, and you
> > are
> > welcome to change it and/or distribute copies of it under certain
> > conditions.
> > Type "show copying" to see the conditions.
> > There is absolutely no warranty for GDB.  Type "show warranty" for
> > details.
> > This GDB was configured as "--host=i586-pc-linux-gnu
> > --target=i386-elf"...
> > (gdb) set remotebaud 38400
> > (gdb) target remote /dev/ttyS0
> > Remote debugging using /dev/ttyS0
> > Ignoring packet error, continuing...
> > Ignoring packet error, continuing...
> > Ignoring packet error, continuing...
> > Couldn't establish connection to remote target
> > Malformed response to offset query, timeout
> > (gdb) load
> > You can't do that when your target is `exec'
> >
> > If I type i386-elf-gdb hello instead,
> > the graphic window shows up since I installed insight,
> >
> > I saw the source code of atexit.cxx is shown in the window, under Run
> > menu,
> > I click on "connect to target" menuitem, and set target be "remote
> > serial",
> > and baud rate is 38400, and port is /dev/ttyS0, I clicked Ok, nothing
> > happens,
> > then I click "connect to target" menuitem under Run menu again, then
> > a dialog shows "Successfully connected". Then I click on "ok" button on
> > this
> > dialog, but the insight will exit and shows me "segmentation fault".
> >
> > Anyway, I cannot connect to the target to do remote debugging, I guess
> > there is something wrong with physical connection to the target machine.
> >
> > On the host (intel Redhat 7.0 machine), there are two ports with D9
> > interface, I don't know how to distinguish between com1 and com2, so I
> > just tried both of them, and got the same results above.(on my target
> > machine,
> >  there is only one D9 interface).
> >
> >
> > Please tell me what is wrong and what should I do so that I can
> > do remote debugging. thanks a lot.
> >
> >



More information about the Ecos-discuss mailing list