☠ Buildbot (Sourceware): binutils-gdb - failed test (failure) (master)

[Sam James]

builder--- via Binutils <binutils@sourceware.org> writes:

> A new failure has been detected on builder binutils-gentoo-sparc while building binutils-gdb.
>
> Full details are available at:
>     https://builder.sourceware.org/buildbot/#builders/228/builds/1286

I'll reboot, but interestingly, no RCU issues in dmesg at the moment...

>
> Build state: failed test (failure)
> Revision: 8b8050d46d3fe19ab3cec1e709accd6519e506ae
> Worker: gentoo-sparc
> Build Reason: (unknown)
> Blamelist: GDB Administrator <gdbadmin@sourceware.org>
>
> Steps:
>
> - 0: worker_preparation ( success )
>
> - 1: git checkout ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/1/logs/stdio
>
> - 2: rm -rf binutils-build ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/2/logs/stdio
>
> - 3: configure ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/3/logs/stdio
>         - config.log: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/3/logs/config_log
>
> - 4: make ( warnings )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/4/logs/stdio
>         - warnings (21): https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/4/logs/warnings__21_
>
> - 5: make check ( failure )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/stdio
>         - ld.sum: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/ld_sum
>         - ld.log: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/ld_log
>         - gas.sum: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/gas_sum
>         - gas.log: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/gas_log
>         - binutils.sum: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/binutils_sum
>         - binutils.log: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/binutils_log
>         - libsframe.sum: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/libsframe_sum
>         - libsframe.log: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/libsframe_log
>         - libctf.sum: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/libctf_sum
>         - libctf.log: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/libctf_log
>         - warnings (12): https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/5/logs/warnings__12_
>
> - 6: prep ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/6/logs/stdio
>
> - 7: build bunsen.cpio.gz ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/7/logs/stdio
>
> - 8: fetch bunsen.cpio.gz ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/8/logs/stdio
>
> - 9: unpack bunsen.cpio.gz ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/9/logs/stdio
>
> - 10: pass .bunsen.source.gitname ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/10/logs/stdio
>
> - 11: pass .bunsen.source.gitdescribe ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/11/logs/stdio
>
> - 12: pass .bunsen.source.gitbranch ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/12/logs/stdio
>
> - 13: pass .bunsen.source.gitrepo ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/13/logs/stdio
>
> - 14: upload to bunsen ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/14/logs/stdio
>
> - 15: clean up ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/15/logs/stdio
>
> - 16: rm -rf binutils-build_1 ( success )
>     Logs:
>         - stdio: https://builder.sourceware.org/buildbot/#builders/228/builds/1286/steps/16/logs/stdio