This is the mail archive of the
libc-alpha@sourceware.org
mailing list for the glibc project.
Re: [PATCH v5] Add pretty printers for the NPTL lock types
- From: Martin Galvan <martin dot galvan at tallertechnologies dot com>
- To: Siddhesh Poyarekar <sid at reserved-bit dot com>
- Cc: libc-alpha at sourceware dot org, "Carlos O'Donell" <carlos at redhat dot com>, Tom Tromey <tom at tromey dot com>, Daniel Gutson <daniel dot gutson at tallertechnologies dot com>, Roland McGrath <roland at hack dot frob dot com>
- Date: Mon, 25 Apr 2016 18:58:38 -0300
- Subject: Re: [PATCH v5] Add pretty printers for the NPTL lock types
- Authentication-results: sourceware.org; auth=none
- References: <CAOKbPbY87ATbCF=W-6+26vfjw1mkt8aX6TuKLWBB3BANW8N8oQ at mail dot gmail dot com> <1460472939-9725-1-git-send-email-martin dot galvan at tallertechnologies dot com> <20160412155919 dot GG30851 at devel dot intra dot reserved-bit dot com> <CAOKbPbbfGXQMnoNBDbMcJKO5rgK-Fipx+1rYHvdynjeke5Jeww at mail dot gmail dot com> <20160412185626 dot GH30851 at devel dot intra dot reserved-bit dot com> <CAOKbPbaq3bqdfainY4crdg8cps=FqAAvV90-VZrRYAn41hJKow at mail dot gmail dot com> <CAOKbPbYK-jO78X8sU0HpWgT+1hX7_jz8SZqMcGAHQjk=kDK6iw at mail dot gmail dot com> <CAOKbPbYSx=07d6TRph5aKgtQQQeQhuU0vLEECuQmUE6=oW3aVA at mail dot gmail dot com> <CAOKbPba+=bD2L8jB2sUzgNEHDwKt+97-G-KCPaXZ6sN9EN4jaw at mail dot gmail dot com>
Pinging this again. A question before I send v6: Roland mentioned
$(py-const) shouldn't be part of before-compile since that's only for
stuff that must exist before C code can be compiled. However, if I
take it out the $(py-const) target won'r run. Where should I place it?
On Wed, Apr 20, 2016 at 9:43 AM, Martin Galvan
<martin.galvan@tallertechnologies.com> wrote:
> Pinging this again. If there's still no response in the following days
> I'll send a v6 with the same directory structure.
>
> On Mon, Apr 18, 2016 at 11:10 AM, Martin Galvan
> <martin.galvan@tallertechnologies.com> wrote:
>> Pinging this since there was no response.
>>
>> On Tue, Apr 12, 2016 at 6:27 PM, Martin Galvan
>> <martin.galvan@tallertechnologies.com> wrote:
>>> So far it appears to be working fine. I'll fix the other cosmetic
>>> issues and wait for Roland and Carlos' response before
>>> sending v6.
>
>
>
> --
>
>
> Martin Galvan
>
> Software Engineer
>
> Taller Technologies Argentina
>
>
> San Lorenzo 47, 3rd Floor, Office 5
>
> CÃrdoba, Argentina
>
> Phone: 54 351 4217888 / +54 351 4218211
--
Martin Galvan
Software Engineer
Taller Technologies Argentina
San Lorenzo 47, 3rd Floor, Office 5
CÃrdoba, Argentina
Phone: 54 351 4217888 / +54 351 4218211