This is the mail archive of the crossgcc@sourceware.org mailing list for the crossgcc project.

See the CrossGCC FAQ for lots more information.


Index Nav: [Date Index] [Subject Index] [Author Index] [Thread Index]
Message Nav: [Date Prev] [Date Next] [Thread Prev] [Thread Next]
Other format: [Raw text]

[PATCH] full patch file for (new) gcc-4.1-20051015/ patch subdirectory


  a slightly tweaked version of the same "gcc-4.1-fix-fixincl.patch"
patch file that is found in earlier versions of gcc-4.1 snapshots.
the only difference is that the second hunk applied against
Makefile.in adds an extra test of ! $(inhibit_libc) in that "if"
statement, without which the patch attempt fails.

rday


========================================================================

See http://gcc.gnu.org/PR22541

From: Dan Kegel

When building gcc-3.4.3 or gcc-4.x into a clean $PREFIX,
the configure script happily copies the glibc include files from include to sys-include;
here's the line from the log file (with $PREFIX instead of the real prefix):

Copying $PREFIX/i686-unknown-linux-gnu/include to $PREFIX/i686-unknown-linux-gnu/sys-include

But later, when running fixincludes, it gives the error message
 The directory that should contain system headers does not exist:
  $PREFIX/lib/gcc/i686-unknown-linux-gnu/3.4.3/../../../../i686-unknown-linux-gnu/sys-include

Nevertheless, it continues building; the header files it installs in
 $PREFIX/lib/gcc/i686-unknown-linux-gnu/3.4.3/include
do not include the boilerplate that would cause it to #include_next the
glibc headers in the system header directory.
Thus the resulting toolchain can't compile the following program:
#include <limits.h>
int x = PATH_MAX;
because its limits.h doesn't include the glibc header.

The problem is that gcc/Makefile.in assumes that
it can refer to $PREFIX/i686-unknown-linux-gnu  with the path
                $PREFIX/lib/../i686-unknown-linux-gnu, but
that fails because the directory $PREFIX/lib doesn't exist during 'make all';
it is only created later, during 'make install'.  (Which makes this problem
confusing, since one only notices the breakage well after 'make install',
at which point the path configure complained about does exist, and has the
right stuff in it.)

A fix that I've been using for a while is to use sed to canonicalize
the path.  The sed syntax is a bit obtuse, but it works.

(hey, that's the first time I've ever used a label in a sed script; thanks to the sed faq
for explaining the :a ... ta method of looping to repeat a search-and-replace until it doesn't match.)

[rediffed against gcc-4.1-20051015]

--- gcc-4.1-20051015/gcc/Makefile.in.old	2005-07-11 09:25:37.171541744 -0700
+++ gcc-4.1-20051015/gcc/Makefile.in	2005-07-11 09:30:27.203450192 -0700
@@ -388,7 +388,10 @@
 CROSS_SYSTEM_HEADER_DIR = @CROSS_SYSTEM_HEADER_DIR@

 # autoconf sets SYSTEM_HEADER_DIR to one of the above.
-SYSTEM_HEADER_DIR = @SYSTEM_HEADER_DIR@
+# Purge it of unneccessary internal relative paths
+# to directories that might not exist yet.
+# The sed idiom for this is to repeat the search-and-replace until it doesn't match, using :a ... ta.
+SYSTEM_HEADER_DIR = `echo @SYSTEM_HEADER_DIR@ | sed -e :a -e "s,[^/]*/\.\.\/,," -e ta`

 # Control whether to run fixproto and fixincludes.
 STMP_FIXPROTO = @STMP_FIXPROTO@
@@ -3163,13 +3166,15 @@
 ../$(build_subdir)/fixincludes/fixincl: ; @ :

 # Build fixed copies of system files.
+# Abort if no system headers available, unless building a crosscompiler.
+# Canonicalize path so directory/that/doesnt/exist/yet/../../../.. doesn't fail
 stmp-fixinc: gsyslimits.h macro_list \
   $(build_objdir)/fixincludes/fixincl \
   $(build_objdir)/fixincludes/fixinc.sh
 	@if ! $(inhibit_libc) && test ! -d ${SYSTEM_HEADER_DIR}; then \
 	  echo The directory that should contain system headers does not exist: >&2 ; \
 	  echo "  ${SYSTEM_HEADER_DIR}" >&2 ; \
-	  if test "x${SYSTEM_HEADER_DIR}" = "x${gcc_tooldir}/sys-include"; \
+ 	  if test "x${SYSTEM_HEADER_DIR}" = "x`echo "${gcc_tooldir}/sys-include" | sed -e :a -e "s,[^/]*/\.\.\/,," -e ta`"; \
 	  then sleep 1; else exit 1; fi; \
 	fi
 	rm -rf include; mkdir include



------
Want more information?  See the CrossGCC FAQ, http://www.objsw.com/CrossGCC/
Want to unsubscribe? Send a note to crossgcc-unsubscribe@sources.redhat.com


Index Nav: [Date Index] [Subject Index] [Author Index] [Thread Index]
Message Nav: [Date Prev] [Date Next] [Thread Prev] [Thread Next]