Alan Modra [Sat, 17 Aug 2013 09:17:22 +0000 (18:47 +0930)]
PowerPC LE memcpy
http://sourceware.org/ml/libc-alpha/2013-08/msg00103.html
LIttle-endian support for memcpy. I spent some time cleaning up the
64-bit power7 memcpy, in order to avoid the extra alignment traps
power7 takes for little-endian. It probably would have been better
to copy the linux kernel version of memcpy.
* sysdeps/powerpc/powerpc32/power4/memcpy.S: Add little endian support.
* sysdeps/powerpc/powerpc32/power6/memcpy.S: Likewise.
* sysdeps/powerpc/powerpc32/power7/memcpy.S: Likewise.
* sysdeps/powerpc/powerpc32/power7/mempcpy.S: Likewise.
* sysdeps/powerpc/powerpc64/memcpy.S: Likewise.
* sysdeps/powerpc/powerpc64/power4/memcpy.S: Likewise.
* sysdeps/powerpc/powerpc64/power6/memcpy.S: Likewise.
* sysdeps/powerpc/powerpc64/power7/memcpy.S: Likewise.
* sysdeps/powerpc/powerpc64/power7/mempcpy.S: Likewise. Make better
use of regs. Use power7 mtocrf. Tidy function tails.
Alan Modra [Sat, 17 Aug 2013 09:16:47 +0000 (18:46 +0930)]
PowerPC LE memcmp
http://sourceware.org/ml/libc-alpha/2013-08/msg00102.html
This is a rather large patch due to formatting and renaming. The
formatting changes were to make it possible to compare power7 and
power4 versions of memcmp. Using different register defines came
about while I was wrestling with the code, trying to find spare
registers at one stage. I found it much simpler if we refer to a reg
by the same name throughout a function, so it's better if short-term
multiple use regs like rTMP are referred to using their register
number. I made the cr field usage changes when attempting to reload
rWORDn regs in the exit path to byte swap before comparing when
little-endian. That proved a bad idea due to the pipelining involved
in the main loop; Offsets to reload the regs were different first
time around the loop.. Anyway, I left the cr field usage changes in
place for consistency.
Aside from these more-or-less cosmetic changes, I fixed a number of
places where an early exit path restores regs unnecessarily, removed
some dead code, and optimised one or two exits.
* sysdeps/powerpc/powerpc64/power7/memcmp.S: Add little-endian support.
Formatting. Consistently use rXXX register defines or rN defines.
Use early exit labels that avoid restoring unused non-volatile regs.
Make cr field use more consistent with rWORDn compares. Rename
regs used as shift registers for unaligned loop, using rN defines
for short lifetime/multiple use regs.
* sysdeps/powerpc/powerpc64/power4/memcmp.S: Likewise.
* sysdeps/powerpc/powerpc32/power7/memcmp.S: Likewise. Exit with
addi 1,1,64 to pop stack frame. Simplify return value code.
* sysdeps/powerpc/powerpc32/power4/memcmp.S: Likewise.
Alan Modra [Sat, 17 Aug 2013 09:16:05 +0000 (18:46 +0930)]
PowerPC LE strchr
http://sourceware.org/ml/libc-alpha/2013-08/msg00101.html
Adds little-endian support to optimised strchr assembly. I've also
tweaked the big-endian code a little. In power7/strchr.S there's a
check in the tail of the function that we didn't match 0 before
finding a c match, done by comparing leading zero counts. It's just
as valid, and quicker, to compare the raw output from cmpb.
Another little tweak is to use rldimi/insrdi in place of rlwimi for
the power7 strchr functions. Since rlwimi is cracked, it is a few
cycles slower. rldimi can be used on the 32-bit power7 functions
too.
* sysdeps/powerpc/powerpc64/power7/strchr.S (strchr): Add little-endian
support. Correct typos, formatting. Optimize tail. Use insrdi
rather than rlwimi.
* sysdeps/powerpc/powerpc32/power7/strchr.S: Likewise.
* sysdeps/powerpc/powerpc64/power7/strchrnul.S (__strchrnul): Add
little-endian support. Correct typos.
* sysdeps/powerpc/powerpc32/power7/strchrnul.S: Likewise. Use insrdi
rather than rlwimi.
* sysdeps/powerpc/powerpc64/strchr.S (rTMP4, rTMP5): Define. Use
in loop and entry code to keep "and." results.
(strchr): Add little-endian support. Comment. Move cntlzd
earlier in tail.
* sysdeps/powerpc/powerpc32/strchr.S: Likewise.
Alan Modra [Sat, 17 Aug 2013 09:11:17 +0000 (18:41 +0930)]
PowerPC LE strcmp and strncmp
http://sourceware.org/ml/libc-alpha/2013-08/msg00099.html
More little-endian support. I leave the main strcmp loops unchanged,
(well, except for renumbering rTMP to something other than r0 since
it's needed in an addi insn) and modify the tail for little-endian.
I noticed some of the big-endian tail code was a little untidy so have
cleaned that up too.
Alan Modra [Sat, 17 Aug 2013 09:10:48 +0000 (18:40 +0930)]
PowerPC LE strnlen
http://sourceware.org/ml/libc-alpha/2013-08/msg00098.html
The existing strnlen code has a number of defects, so this patch is more
than just adding little-endian support. The changes here are similar to
those for memchr.
* sysdeps/powerpc/powerpc64/power7/strnlen.S (strnlen): Add
little-endian support. Remove unnecessary "are we done" tests.
Handle "s" wrapping around zero and extremely large "size".
Correct main loop count. Handle single left-over word from main
loop inline rather than by using small_loop. Correct comments.
Delete "zero" tail, use "end_max" instead.
* sysdeps/powerpc/powerpc32/power7/strnlen.S: Likewise.
Alan Modra [Sat, 17 Aug 2013 09:10:11 +0000 (18:40 +0930)]
PowerPC LE strlen
http://sourceware.org/ml/libc-alpha/2013-08/msg00097.html
This is the first of nine patches adding little-endian support to the
existing optimised string and memory functions. I did spend some
time with a power7 simulator looking at cycle by cycle behaviour for
memchr, but most of these patches have not been run on cpu simulators
to check that we are going as fast as possible. I'm sure PowerPC can
do better. However, the little-endian support mostly leaves main
loops unchanged, so I'm banking on previous authors having done a
good job on big-endian.. As with most code you stare at long enough,
I found some improvements for big-endian too.
Little-endian support for strlen. Like most of the string functions,
I leave the main word or multiple-word loops substantially unchanged,
just needing to modify the tail.
Removing the branch in the power7 functions is just a tidy. .align
produces a branch anyway. Modifying regs in the non-power7 functions
is to suit the new little-endian tail.
* sysdeps/powerpc/powerpc64/power7/strlen.S (strlen): Add little-endian
support. Don't branch over align.
* sysdeps/powerpc/powerpc32/power7/strlen.S: Likewise.
* sysdeps/powerpc/powerpc64/strlen.S (strlen): Add little-endian support.
Rearrange tmp reg use to suit. Comment.
* sysdeps/powerpc/powerpc32/strlen.S: Likewise.
This copies the sparc version of sigstack.h, which gives powerpc
#define MINSIGSTKSZ 4096
#define SIGSTKSZ 16384
Before the VSX changes, struct rt_sigframe size was 1920 plus 128 for
__SIGNAL_FRAMESIZE giving ppc64 exactly the default MINSIGSTKSZ of
2048.
After VSX, ucontext increased by 256 bytes. Oops, we're over
MINSIGSTKSZ, so powerpc has been using the wrong value for quite a
while. Add another ucontext for TM and rt_sigframe is now at 3872,
giving actual MINSIGSTKSZ of 4000.
The glibc testcase that I was looking at was tst-cancel21, which
allocates 2*SIGSTKSZ (not because the test is trying to be
conservative, but because the test actually has nested signal stack
frames). We blew the allocation by 48 bytes when using current
mainline gcc to compile glibc (le ppc64).
The required stack depth in _dl_lookup_symbol_x from the top of the
next signal frame was 10944 bytes. I guess you'd want to add 288 to
that, implying an actual SIGSTKSZ of 11232.
* sysdeps/unix/sysv/linux/powerpc/bits/sigstack.h: New file.
Use conditional form of branch and link to avoid destroying the cpu
link stack used to predict blr return addresses.
* sysdeps/unix/sysv/linux/powerpc/powerpc32/makecontext.S: Use
conditional form of branch and link when obtaining pc.
* sysdeps/unix/sysv/linux/powerpc/powerpc64/makecontext.S: Likewise.
Alan Modra [Sat, 17 Aug 2013 09:05:40 +0000 (18:35 +0930)]
PowerPC ugly symbol versioning
http://sourceware.org/ml/libc-alpha/2013-08/msg00090.html
This patch fixes symbol versioning in setjmp/longjmp. The existing
code uses raw versions, which results in wrong symbol versioning when
you want to build glibc with a base version of 2.19 for LE.
Note that the merging the 64-bit and 32-bit versions in novmx-lonjmp.c
and pt-longjmp.c doesn't result in GLIBC_2.0 versions for 64-bit, due
to the base in shlib_versions.
Anton Blanchard [Sat, 17 Aug 2013 09:04:40 +0000 (18:34 +0930)]
PowerPC LE setjmp/longjmp
http://sourceware.org/ml/libc-alpha/2013-08/msg00089.html
Little-endian fixes for setjmp/longjmp. When writing these I noticed
the setjmp code corrupts the non volatile VMX registers when using an
unaligned buffer. Anton fixed this, and also simplified it quite a
bit.
The current code uses boilerplate for the case where we want to store
16 bytes to an unaligned address. For that we have to do a
read/modify/write of two aligned 16 byte quantities. In our case we
are storing a bunch of back to back data (consective VMX registers),
and only the start and end of the region need the read/modify/write.
Alan Modra [Sat, 17 Aug 2013 09:02:18 +0000 (18:32 +0930)]
PowerPC floating point little-endian [13 of 15]
http://sourceware.org/ml/libc-alpha/2013-08/msg00088.html
* sysdeps/powerpc/powerpc32/fpu/s_roundf.S: Increase alignment of
constants to usual value for .cst8 section, and remove redundant
high address load.
* sysdeps/powerpc/powerpc32/power4/fpu/s_llround.S: Use float
constant for 0x1p52. Load little-endian words of double from
correct stack offsets.
Alan Modra [Sat, 17 Aug 2013 09:00:23 +0000 (18:30 +0930)]
PowerPC floating point little-endian [10 of 15]
http://sourceware.org/ml/libc-alpha/2013-07/msg00201.html
These two functions oddly test x+1>0 when a double x is >= 0.0, and
similarly when x is negative. I don't see the point of that since the
test should always be true. I also don't see any need to convert x+1
to integer rather than simply using xr+1. Note that the standard
allows these functions to return any value when the input is outside
the range of long long, but it's not too hard to prevent xr+1
overflowing so that's what I've done.
(With rounding mode FE_UPWARD, x+1 can be a lot more than what you
might naively expect, but perhaps that situation was covered by the
x - xrf < 1.0 test.)
Alan Modra [Sat, 17 Aug 2013 08:59:43 +0000 (18:29 +0930)]
PowerPC floating point little-endian [9 of 15]
http://sourceware.org/ml/libc-alpha/2013-07/msg00200.html
This works around the fact that vsx is disabled in current
little-endian gcc. Also, float constants take 4 bytes in memory
vs. 16 bytes for vector constants, and we don't need to write one lot
of masks for double (register format) and another for float (mem
format).
* sysdeps/powerpc/fpu/s_float_bitwise.h (__float_and_test28): Don't
use vector int constants.
(__float_and_test24, __float_and8, __float_get_exp): Likewise.
Alan Modra [Sat, 17 Aug 2013 08:57:19 +0000 (18:27 +0930)]
PowerPC floating point little-endian [6 of 15]
http://sourceware.org/ml/libc-alpha/2013-07/msg00197.html
A rewrite to make this code correct for little-endian.
* sysdeps/ieee754/ldbl-128ibm/e_sqrtl.c (mynumber): Replace
union 32-bit int array member with 64-bit int array.
(t515, tm256): Double rather than long double.
(__ieee754_sqrtl): Rewrite using 64-bit arithmetic.
Alan Modra [Sat, 17 Aug 2013 08:56:39 +0000 (18:26 +0930)]
PowerPC floating point little-endian [5 of 15]
http://sourceware.org/ml/libc-alpha/2013-08/msg00085.html
Rid ourselves of ieee854.
* sysdeps/ieee754/ldbl-128ibm/ieee754.h (union ieee854_long_double):
Delete.
(IEEE854_LONG_DOUBLE_BIAS): Delete.
* sysdeps/ieee754/ldbl-128ibm/math_ldbl.h: Don't include ieee854
version of math_ldbl.h.
Alan Modra [Sat, 17 Aug 2013 08:55:51 +0000 (18:25 +0930)]
PowerPC floating point little-endian [4 of 15]
http://sourceware.org/ml/libc-alpha/2013-08/msg00084.html
Another batch of ieee854 macros and union replacement. These four
files also have bugs fixed with this patch. The fact that the two
doubles in an IBM long double may have different signs means that
negation and absolute value operations can't just twiddle one sign bit
as you can with ieee864 style extended double. fmodl, remainderl,
erfl and erfcl all had errors of this type. erfl also returned +1 for
large magnitude negative input where it should return -1. The hypotl
error is innocuous since the value adjusted twice is only used as a
flag. The e_hypotl.c tests for large "a" and small "b" are mutually
exclusive because we've already exited when x/y > 2**120. That allows
some further small simplifications.
[BZ #15734], [BZ #15735]
* sysdeps/ieee754/ldbl-128ibm/e_fmodl.c (__ieee754_fmodl): Rewrite
all uses of ieee875 long double macros and unions. Simplify test
for 0.0L. Correct |x|<|y| and |x|=|y| test. Use
ldbl_extract_mantissa value for ix,iy exponents. Properly
normalize after ldbl_extract_mantissa, and don't add hidden bit
already handled. Don't treat low word of ieee854 mantissa like
low word of IBM long double and mask off bit when testing for
zero.
* sysdeps/ieee754/ldbl-128ibm/e_hypotl.c (__ieee754_hypotl): Rewrite
all uses of ieee875 long double macros and unions. Simplify tests
for 0.0L and inf. Correct double adjustment of k. Delete dead code
adjusting ha,hb. Simplify code setting kld. Delete two600 and
two1022, instead use their values. Recognise that tests for large
"a" and small "b" are mutually exclusive. Rename vars. Comment.
* sysdeps/ieee754/ldbl-128ibm/e_remainderl.c (__ieee754_remainderl):
Rewrite all uses of ieee875 long double macros and unions. Simplify
test for 0.0L and nan. Correct negation.
* sysdeps/ieee754/ldbl-128ibm/s_erfl.c (__erfl): Rewrite all uses of
ieee875 long double macros and unions. Correct output for large
magnitude x. Correct absolute value calculation.
(__erfcl): Likewise.
* math/libm-test.inc: Add tests for errors discovered in IBM long
double versions of fmodl, remainderl, erfl and erfcl.
Alan Modra [Sat, 17 Aug 2013 08:54:58 +0000 (18:24 +0930)]
PowerPC floating point little-endian [3 of 15]
http://sourceware.org/ml/libc-alpha/2013-08/msg00083.html
Further replacement of ieee854 macros and unions. These files also
have some optimisations for comparison against 0.0L, infinity and nan.
Since the ABI specifies that the high double of an IBM long double
pair is the value rounded to double, a high double of 0.0 means the
low double must also be 0.0. The ABI also says that infinity and
nan are encoded in the high double, with the low double unspecified.
This means that tests for 0.0L, +/-Infinity and +/-NaN need only check
the high double.
* sysdeps/ieee754/ldbl-128ibm/e_atan2l.c (__ieee754_atan2l): Rewrite
all uses of ieee854 long double macros and unions. Simplify tests
for long doubles that are fully specified by the high double.
* sysdeps/ieee754/ldbl-128ibm/e_gammal_r.c (__ieee754_gammal_r):
Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_ilogbl.c (__ieee754_ilogbl): Likewise.
Remove dead code too.
* sysdeps/ieee754/ldbl-128ibm/e_jnl.c (__ieee754_jnl): Likewise.
(__ieee754_ynl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_log10l.c (__ieee754_log10l): Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_logl.c (__ieee754_logl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_powl.c (__ieee754_powl): Likewise.
Remove dead code too.
* sysdeps/ieee754/ldbl-128ibm/k_tanl.c (__kernel_tanl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_expm1l.c (__expm1l): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_frexpl.c (__frexpl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_isinf_nsl.c (__isinf_nsl): Likewise.
Simplify.
* sysdeps/ieee754/ldbl-128ibm/s_isinfl.c (___isinfl): Likewise.
Simplify.
* sysdeps/ieee754/ldbl-128ibm/s_log1pl.c (__log1pl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_modfl.c (__modfl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_nextafterl.c (__nextafterl): Likewise.
Comment on variable precision.
* sysdeps/ieee754/ldbl-128ibm/s_nexttoward.c (__nexttoward): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_nexttowardf.c (__nexttowardf):
Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_remquol.c (__remquol): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_scalblnl.c (__scalblnl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_scalbnl.c (__scalbnl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_tanhl.c (__tanhl): Likewise.
* sysdeps/powerpc/fpu/libm-test-ulps: Adjust tan_towardzero ulps.
Alan Modra [Sat, 17 Aug 2013 08:54:05 +0000 (18:24 +0930)]
PowerPC floating point little-endian [2 of 15]
http://sourceware.org/ml/libc-alpha/2013-08/msg00082.html
This patch replaces occurrences of GET_LDOUBLE_* and SET_LDOUBLE_*
macros, and union ieee854_long_double_shape_type in ldbl-128ibm/,
and a stray one in the 32-bit fpu support. These files have no
significant changes apart from rewriting the long double bit access.
Alan Modra [Sat, 17 Aug 2013 08:51:58 +0000 (18:21 +0930)]
PowerPC floating point little-endian [1 of 15]
http://sourceware.org/ml/libc-alpha/2013-08/msg00081.html
This is the first of a series of patches to ban ieee854_long_double
and the ieee854_long_double macros when using IBM long double. union
ieee854_long_double just isn't correct for IBM long double, especially
when little-endian, and pretending it is OK has allowed a number of
bugs to remain undetected in sysdeps/ieee754/ldbl-128ibm/.
This changes the few places in generic code that use it.
* stdio-common/printf_size.c (__printf_size): Don't use
union ieee854_long_double in fpnum union.
* stdio-common/printf_fphex.c (__printf_fphex): Likewise. Use
signbit macro to retrieve sign from long double.
* stdio-common/printf_fp.c (___printf_fp): Use signbit macro to
retrieve sign from long double.
* sysdeps/ieee754/ldbl-128ibm/printf_fphex.c: Adjust for fpnum change.
* sysdeps/ieee754/ldbl-128/printf_fphex.c: Likewise.
* sysdeps/ieee754/ldbl-96/printf_fphex.c: Likewise.
* sysdeps/x86_64/fpu/printf_fphex.c: Likewise.
* math/test-misc.c (main): Don't use union ieee854_long_double.
ports/
* sysdeps/ia64/fpu/printf_fphex.c: Adjust for fpnum change.
Alan Modra [Sat, 17 Aug 2013 08:49:44 +0000 (18:19 +0930)]
Fix for [BZ #15680] IBM long double inaccuracy
http://sourceware.org/ml/libc-alpha/2013-06/msg00919.html
I discovered a number of places where denormals and other corner cases
were being handled wrongly.
- printf_fphex.c: Testing for the low double exponent being zero is
unnecessary. If the difference in exponents is less than 53 then the
high double exponent must be nearing the low end of its range, and the
low double exponent hit rock bottom.
- ldbl2mpn.c: A denormal (ie. exponent of zero) value is treated as
if the exponent was one, so shift mantissa left by one. Code handling
normalisation of the low double mantissa lacked a test for shift count
greater than bits in type being shifted, and lacked anything to handle
the case where the difference in exponents is less than 53 as in
printf_fphex.c.
- math_ldbl.h (ldbl_extract_mantissa): Same as above, but worse, with
code testing for exponent > 1 for some reason, probably a typo for >= 1.
- math_ldbl.h (ldbl_insert_mantissa): Round the high double as per
mpn2ldbl.c (hi is odd or explicit mantissas non-zero) so that the
number we return won't change when applying ldbl_canonicalize().
Add missing overflow checks and normalisation of high mantissa.
Correct misleading comment: "The hidden bit of the lo mantissa is
zero" is not always true as can be seen from the code rounding the hi
mantissa. Also by inspection, lzcount can never be less than zero so
remove that test. Lastly, masking bitfields to their widths can be
left to the compiler.
- mpn2ldbl.c: The overflow checks here on rounding of high double were
just plain wrong. Incrementing the exponent must be accompanied by a
shift right of the mantissa to keep the value unchanged. Above notes
for ldbl_insert_mantissa are also relevant.
[BZ #15680]
* sysdeps/ieee754/ldbl-128ibm/e_rem_pio2l.c: Comment fix.
* sysdeps/ieee754/ldbl-128ibm/printf_fphex.c
(PRINT_FPHEX_LONG_DOUBLE): Tidy code by moving -53 into ediff
calculation. Remove unnecessary test for denormal exponent.
* sysdeps/ieee754/ldbl-128ibm/ldbl2mpn.c (__mpn_extract_long_double):
Correct handling of denormals. Avoid undefined shift behaviour.
Correct normalisation of low mantissa when low double is denormal.
* sysdeps/ieee754/ldbl-128ibm/math_ldbl.h
(ldbl_extract_mantissa): Likewise. Comment. Use uint64_t* for hi64.
(ldbl_insert_mantissa): Make both hi64 and lo64 parms uint64_t.
Correct normalisation of low mantissa. Test for overflow of high
mantissa and normalise.
(ldbl_nearbyint): Use more readable constant for two52.
* sysdeps/ieee754/ldbl-128ibm/mpn2ldbl.c
(__mpn_construct_long_double): Fix test for overflow of high
mantissa and correct normalisation. Avoid undefined shift.
Alan Modra [Sat, 17 Aug 2013 08:42:56 +0000 (18:12 +0930)]
IBM long double mechanical changes to support little-endian
http://sourceware.org/ml/libc-alpha/2013-07/msg00001.html
This patch starts the process of supporting powerpc64 little-endian
long double in glibc. IBM long double is an array of two ieee
doubles, so making union ibm_extended_long_double reflect this fact is
the correct way to access fields of the doubles.
* sysdeps/ieee754/ldbl-128ibm/ieee754.h
(union ibm_extended_long_double): Define as an array of ieee754_double.
(IBM_EXTENDED_LONG_DOUBLE_BIAS): Delete.
* sysdeps/ieee754/ldbl-128ibm/printf_fphex.c: Update all references
to ibm_extended_long_double and IBM_EXTENDED_LONG_DOUBLE_BIAS.
* sysdeps/ieee754/ldbl-128ibm/e_exp10l.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_expl.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/ldbl2mpn.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/math_ldbl.h: Likewise.
* sysdeps/ieee754/ldbl-128ibm/mpn2ldbl.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_nearbyintl.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/strtold_l.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/x2y2m1l.c: Likewise.
Brooks Moses [Thu, 3 Oct 2013 17:38:14 +0000 (10:38 -0700)]
Fix erroneous (and circular) implied pattern rule for linkobj/libc.so.
[BZ #15915] As described in the bug, the pattern rule for lib%.so files
in Makerules includes linkobj/libc.so as a dependency. However, the
explicit rule for linkobj/libc.so is in the top-level Makefile.
Thus, the subdirectory makefiles that include Makerules end up with an
erroneous makefile pattern rule for linkobj/libc.so that includes
itself as a dependency. The result is make warnings whenever rules
for other .so files are resolved -- and, on occasion, actual makefile
failures when a race condition causes the implicit rule to actually be
used.
This patch moves the explicit rules for linkobj/libc.so into Makerules
to clear up this problem. It also elaborates a couple of comments
that I'd initially found confusing.
Will Newton [Wed, 7 Aug 2013 12:55:30 +0000 (13:55 +0100)]
ARM: Add pointer encryption support.
Add support for pointer encryption in glibc internal structures in C
and assembler code. Pointer encryption is a glibc security feature
described here:
The ARM implementation uses global variables instead of thread pointer
relative accesses to get the value of the pointer encryption guard
because accessing the thread pointer can be very expensive on older
ARM cores.
ports/ChangeLog.arm:
2013-10-03 Will Newton <will.newton@linaro.org>
* sysdeps/arm/__longjmp.S (__longjmp): Demangle fp, sp
and lr when restoring register values.
* sysdeps/arm/include/bits/setjmp.h (JMP_BUF_REGLIST): Remove
sp and lr from list and replace fp with a4.
* sysdeps/arm/jmpbuf-unwind.h (_jmpbuf_sp): New function.
(_JMPBUF_UNWINDS_ADJ): Call _jmpbuf_sp.
* sysdeps/arm/setjmp.S (__sigsetjmp): Mangle fp, sp and lr
before storing register values.
* sysdeps/arm/sysdep.h (LDST_GLOBAL): New macro.
* sysdeps/unix/sysv/linux/arm/sysdep.h (PTR_MANGLE): New macro.
(PTR_DEMANGLE): Likewise. (PTR_MANGLE2): Likewise.
(PTR_DEMANGLE2): Likewise.
Eric Blake [Wed, 4 Sep 2013 23:02:47 +0000 (17:02 -0600)]
glob: silence -Wattribute warnings
Colin Watson reported that some versions of gcc warn about
attribute leaf used on a static function, since it has no
effect on anything but external functions.
* posix/glob.c (next_brace_sub, prefix_array, collated_compare):
Use __THROWNL rather than __THROW on static functions.
Fix PI mutex check in pthread_cond_broadcast and pthread_cond_signal
Fixes BZ #15988.
The check had a typo - it checked for PTHREAD_MUTEX_ROBUST_NP instead
of PTHREAD_MUTEX_ROBUST_NORMAL_NP. It has now been replaced by the
already existing convenience macro USE_REQUEUE_PI.
don't use Bash-specific ${parameter/pattern/string} expansion
sysdeps/unix/make-syscalls.sh and sysdeps/unix/Makefile use GNU Bash's
${parameter/pattern/string} parameter expansion. Non-Bash shells (e.g.
dash or BusyBox ash when built with CONFIG_ASH_BASH_COMPAT disabled)
don't support this expansion syntax. So glibc will fail to build when
$(SHELL) expands to a path that isn't provided by Bash.
An example build failure:
for dir in [...]; do \
test -f $dir/syscalls.list && \
{ sysdirs='[...]' \
asm_CPP='gcc -c -I[...] -D_LIBC_REENTRANT -include include/libc-symbols.h -DASSEMBLER -g -Wa,--noexecstack -E -x assembler-with-cpp' \
/bin/sh sysdeps/unix/make-syscalls.sh $dir || exit 1; }; \
test $dir = sysdeps/unix && break; \
done > [build-dir]/sysd-syscallsT
sysdeps/unix/make-syscalls.sh: line 273: syntax error: bad substitution
This patch simply replaces the three instances of the Bash-only syntax
in these files with an echo and sed command substitution.
Steve Ellcey [Mon, 23 Sep 2013 16:58:30 +0000 (09:58 -0700)]
2013-09-23 Steve Ellcey <sellcey@mips.com>
* sysdeps/mips/math_private.h (libc_feholdexcept_mips): New function.
(libc_feholdexcept): New macro.
(libc_feholdexceptf): New macro.
(libc_feholdexceptl): New macro.
(libc_fesetround_mips): New function.
(libc_fesetround): New macro.
(libc_fesetroundf): New macro.
(libc_fesetroundl): New macro.
(libc_feholdexcept_setround_mips): New function.
(libc_feholdexcept_setround): New macro.
(libc_feholdexcept_setroundf): New macro.
(libc_feholdexcept_setroundl): New macro.
(libc_fesetenv_mips): New function.
(libc_fesetenv): New macro.
(libc_fesetenvf): New macro.
(libc_fesetenvl): New macro.
(libc_feupdateenv_mips): New function.
(libc_feupdateenv): New macro.
(libc_feupdateenvf): New macro.
(libc_feupdateenvl): New macro.
Check for integer overflow in cache size computation in strcoll
strcoll is implemented using a cache for indices and weights of
collation sequences in the strings so that subsequent passes do not
have to search through collation data again. For very large string
inputs, the cache size computation could overflow. In such a case,
use the fallback function that does not cache indices and weights of
collation sequences.
Fall back to non-cached sequence traversal and comparison on malloc fail
strcoll currently falls back to alloca if malloc fails, resulting in a
possible stack overflow. This patch implements sequence traversal and
comparison without caching indices and rules.
Carlos O'Donell [Mon, 23 Sep 2013 05:44:38 +0000 (01:44 -0400)]
BZ #15754: Fix test case for ARM.
Statically built binaries use __pointer_chk_guard_local,
while dynamically built binaries use __pointer_chk_guard.
Provide the right definition depending on the test case
we are building.
Carlos O'Donell [Mon, 23 Sep 2013 04:52:09 +0000 (00:52 -0400)]
BZ #15754: CVE-2013-4788
The pointer guard used for pointer mangling was not initialized for
static applications resulting in the security feature being disabled.
The pointer guard is now correctly initialized to a random value for
static applications. Existing static applications need to be
recompiled to take advantage of the fix.
The test tst-ptrguard1-static and tst-ptrguard1 add regression
coverage to ensure the pointer guards are sufficiently random
and initialized to a default value.