- Assembler input is free format and may appear anywhere on the line.
One instruction may extend across multiple lines or more than one
instruction may appear on the same line. White space (space, tab,
comments or newline) may appear anywhere between tokens. A token must
not have embedded spaces. Tokens include numbers, register names,
keywords, user identifiers, and also some multicharacter special
symbols like "+=", "/*" or "||".
- A semicolon must terminate every instruction. Sometimes a complete
instruction will consist of more than one operation. There are two
cases where this occurs. The first is when two general operations
are combined. Normally a comma separates the different parts, as in
a0= r3.h * r2.l, a1 = r3.l * r2.h ;
The second case occurs when a general instruction is combined with one
or two memory references for joint issue. The latter portions are
set off by a "||" token.
a0 = r3.h * r2.l || r1 = [p3++] || r4 = [i2++];
The assembler treats register names and instruction keywords in a case
insensitive manner. User identifiers are case sensitive. Thus, R3.l,
R3.L, r3.l and r3.L are all equivalent input to the assembler.
Register names are reserved and may not be used as program identifiers.
Some operations (such as "Move Register") require a register pair.
Register pairs are always data registers and are denoted using a colon,
eg., R3:2. The larger number must be written firsts. Note that the
hardware only supports odd-even pairs, eg., R7:6, R5:4, R3:2, and R1:0.
Some instructions (such as –SP (Push Multiple)) require a group of
adjacent registers. Adjacent registers are denoted in the syntax by
the range enclosed in parentheses and separated by a colon, eg., (R7:3).
Again, the larger number appears first.
Portions of a particular register may be individually specified. This
is written with a dot (".") following the register name and then a
letter denoting the desired portion. For 32-bit registers, ".H"
denotes the most significant ("High") portion. ".L" denotes the
least-significant portion. The subdivisions of the 40-bit registers
are described later.
- The set of 40-bit registers A1 and A0 that normally contain data that
is being manipulated. Each accumulator can be accessed in four ways.
one 40-bit register
- The register will be referred to as A1 or A0.
one 32-bit register
- The registers are designated as A1.W or A0.W.
two 16-bit registers
- The registers are designated as A1.H, A1.L, A0.H or A0.L.
one 8-bit register
- The registers are designated as A1.X or A0.X for the bits that
extend beyond bit 31.
- The set of 32-bit registers (R0, R1, R2, R3, R4, R5, R6 and R7) that
normally contain data for manipulation. These are abbreviated as
D-register or Dreg. Data registers can be accessed as 32-bit registers
or as two independent 16-bit registers. The least significant 16 bits
of each register is called the "low" half and is designated with ".L"
following the register name. The most significant 16 bits are called
the "high" half and is designated with ".H" following the name.
R7.L, r2.h, r4.L, R0.H
- The set of 32-bit registers (P0, P1, P2, P3, P4, P5, SP and FP) that
normally contain byte addresses of data structures. These are
abbreviated as P-register or Preg.
p2, p5, fp, sp
Stack Pointer SP
- The stack pointer contains the 32-bit address of the last occupied
byte location in the stack. The stack grows by decrementing the
Frame Pointer FP
- The frame pointer contains the 32-bit address of the previous frame
pointer in the stack. It is located at the top of a frame.
- LT0 and LT1. These registers contain the 32-bit address of the top of
a zero overhead loop.
- LC0 and LC1. These registers contain the 32-bit counter of the zero
overhead loop executions.
- LB0 and LB1. These registers contain the 32-bit address of the bottom
of a zero overhead loop.
- The set of 32-bit registers (I0, I1, I2, I3) that normally contain byte
addresses of data structures. Abbreviated I-register or Ireg.
- The set of 32-bit registers (M0, M1, M2, M3) that normally contain
offset values that are added and subracted to one of the index
registers. Abbreviated as Mreg.
- The set of 32-bit registers (L0, L1, L2, L3) that normally contain the
length in bytes of the circular buffer. Abbreviated as Lreg. Clear
the Lreg to disable circular addressing for the corresponding Ireg.
- The set of 32-bit registers (B0, B1, B2, B3) that normally contain the
base address in bytes of the circular buffer. Abbreviated as Breg.
- The Blackfin family has no hardware floating point but the .float
directive generates ieee floating point numbers for use with software
floating point libraries.
- For detailed information on the Blackfin machine instruction set, see
the Blackfin(r) Processor Instruction Set Reference.